PolySweep - Polymeric Sand - 50lb Bag

Every interlocking pavement system requires the installation of joint sand to minimize paver movement, promote safety and provide an aesthetically pleasing look. Installing PolySweep Polymeric Sand and activating with water will provide you with hardened sand within the pavement joints which helps to reduce sand washout, inhibit weed growth and protect against insect infestation.

Polysweep provides superior strength and long-term durability, rather than gimmicks and false promises. PolySweep's original, time-tested formula provides dependable, haze-free performance and is never difficult to install. PolySweep is the only choice for hardscape projects that require solid performance and value. With each job you build, your reputation is on the line, so don't skimp on the polymeric sand.

PolySweep is made with advanced Clear Set Technology which includes using native sands and the highest quality, clearest synthetic polymers. PolySweep’s formula also contains NO Portland Cement. That means, PolySweep will never leave a haze behind on the surface, and that’s a guarantee.

Field proven and time tested, PolySweep’s Superior Strength formulaoffers long lasting durability. Lab testing indicates that PolySweep performs better than the competition and offers superior cohesion and adhesion as well as the fastest set up. Put your trust in PolySweep the polymeric sand that helps you get Joint Stabilization Done Right.

• For Residential & Commercial Applications such as Driveways, Walkways, Patios, Pool Decks & Concrete Overlays.
• Ideal for Concrete & Clay Pavers, Natural Stone, Cast Stone & Porcelain Tile
• Polysweep is recommended for joints up to 3/4” (max), 1” is acceptable where pavers intersect.
• Ideal for joints 1/16” - 4” wide. HP Nextgel is always the industry’s leading product for the stabilization of concrete pavers & slabs.
  
• Polysweep prevent sand erosion from the pavement joints caused by rain and other water run-off, deters weed growth and insect infestation plus reduces overall pavement maintenance.
• Polysweep are designed to expand and contract during freeze/thaw cycles and remain flexible to resist cracking.
• Distribute PolySweep evenly across surface. Sweep sand into joints until full, being careful not to push product over long distances on the surface. (1.5” min depth when using PolySweep, 1.25” min depth when using X-Treme Wide Joint). After joints are filled, sweep excess product from the surface.
• For Concrete Pavers: Run vibratory compactor over the pavement to allow the vibrations to consolidate sand particles into the joints and reduce voids. For Cast Stone or Natural Stone: Use a vibratory rubber roller tamper or a rubber hammer and a piece of wood (2” x 4”).
• Sweep additional sand into the joints if necessary so that the height of the sand is approximately 1/8” below the pavement surface. (Do not overfill joints.) Remove excess product from the surface. Repeat compaction.
• After joints are filled, sweep surface with broom and then use a leaf blower held on slight angle but close to parallel to surface to remove any excess sand/dust from the top of surface. Take care not to remove any sand from joints.
• Using a hose, gently mist the pavement no greater than 500 sf at a time. Allow water to absorb for approximately 5 minutes and repeat misting process three to four times, each time gradually adding more volume of water. The last watering should be a volume of water sufficient enough to rinse off any residual material from the surface.
• In one of the joints, check the moisture depth in the sand with a screwdriver to see that it has penetrated to at least 1½” for pavers and 1 ¼” for natural stone. Replace sand and only apply additional misting if water hasn’t penetrated at least 1½” for pavers and 1 ¼” for natural stone. For optimal joint performance, be certain the entire sand column is fully saturated
• Any residual surface water caught in the texture of the pavers or natural stone should be blown off the surface with a leaf blower.
• When using PolySweep on concrete overlays (pavers/stones installed directly on concrete), a minimum of 1% slope to the concrete and a 1” layer of bedding sand on top of concrete is required. Do not allow water to be trapped in the system. Any water that enters the surface of concrete overlay applications must be allowed to escape the sand setting bed at the outside perimeter of the project. If pavers or stone are set directly on top of the concrete, drill 1” drainage holes thru the concrete with a coverage rate of 1 hole/sq. ft. Fill holes with open graded gravel and covered with geotextile (to keep polymeric sand from migrating into the holes). Drainage channels in lieu of holes in the concrete can also be installed.

• Prior to installation of Polysweep, make sure pavement joints and surface are completely dry AND there is no rain forecasted for at least 12 hours after installation. Polysweep needs to surpass the set up threshold before getting rained on. If there is a possibility of rain shortly after installation, cover project with a tarp. Remove tarp as soon as threat of rain is gone.
• PolySweep should be installed when the average ambient air temperature is above 35 degrees for a minimum of 48 hours after installation.
• Always wear personal protection equipment: eyewear and respirator.
• PolySweep is designed to work best when following ICPI recommended best practices for base installation. Concrete pavers, slabs and natural stone should have ¾” modified stone base and concrete sand setting bed that conforms to ASTM-C33.
• Do not apply too much water too fast as to flood the pavement or erode sand from paver joints.
• Prior to applying Polysweep with natural stone, be sure the surface is free of any dust or stone residue by rinsing thoroughly with water. Then, make sure the natural stone and joints are completely dry prior to installing polymeric sand.
• Do not apply this product to any wet or damp surface because the polymeric sand will adhere to the surface and is difficult to remove.
• This product is not designed for vertical applications and is not a substitute for mortar on vertical or horizontal applications.
• Do not mix or dilute polymeric sand with any other product.
• PolySweep MUST BE STORED in a dry location protected from rain and moisture. Intact, covered pallets can be stored outdoors.